fedora-docs-l10n/fedora-install-guide/f31/pages/_partials/install/StorageSpoke — Korean @ Fedora Weblate: anaconda/StorageSpoke

Translation

English type: Target for macro image

Korean

Needs editing

Skip

	English	Korean	Actions
	Installation Destination	설치 대상
	The `Installation Destination` screen allows you to configure storage options - namely, which disks will be used as the installation target for your {PRODUCT} installation. At least one disk must always be selected for the installation to proceed.	`설치 대상` 화면은 저장소 선택을 구성 할 수 있도록 합니다 - 다시 말하면, 해당 디스크는 자신의 {PRODUCT} 설치를 위한 설치 대상으로 사용 될 것입니다. 적어도 하나의 디스크는 항상 설치 진행을 위해 선택해야만 합니다.
	For information about the theory and concepts behind disk partitioning in Linux, see xref:Installing_Using_Anaconda.adoc#sect-installation-gui-manual-partitioning-recommended[Recommended Partitioning Scheme].	리눅스에서 디스크 파티션에 대한 이론과 개념에 대한 정보를 위해, xref:Installing_Using_Anaconda.adoc#sect-installation-gui-manual-partitioning-recommended[추천된 디스크 파티션 구조] 부분을 참고하세요.
	If you plan to use a disk which already contains some data - for example, if you want to shrink an existing Microsoft Windows partition and install {PRODUCT} as a second system or if you are upgrading a previous release of {PRODUCT}, make sure to back up any important data first. Manipulating partitions always carries a risk - if the process is interrupted or fails for any reason (installer error, hardware failure, power outage, etc.), any data already on the disk may become impossible to recover.
	The Installation Destination screen. There are two local standard disks available	설치 대상 화면. 두 개의 로컬 표준 디스크를 사용 할 수 있습니다
	anaconda/StorageSpoke.png	아나콘다/StorageSpoke.png
	In the top part of the screen, all locally available storage devices (SATA, IDE and SCSI hard drives, USB flash drives, etc.) are displayed in the `Local Standard Disks` section. Local disks are detected when the installer starts - any storage devices connected after the installation has started will not be shown.	화면의 상단 부분에서, 모든 로컬에서 사용 가능한 저장 장치(SATA, IDE 및 SCSI 하드 드라이브, USB 저장장치 등)는 `로컬 표준 디스크` 부분에서 표시됩니다. 로컬 디스크는 설치자가 시작 할 때에 감지됩니다 - 설치가 시작 되었을 때에 연결된 모든 저장장치는 보이지 않을 수 있습니다.
	If you need to configure additional local storage devices, select `I will configure partitioning` and press `Done` to move to xref:Installing_Using_Anaconda.adoc#sect-installation-gui-manual-partitioning[Manual Partitioning]. Then, connect any new hard drives you want to make available during the installation, and press the button marked by a circular arrow in the set of controls below the list of mount points on the left side of the screen. In the dialog window that opens, press `Rescan Disks` and wait until the scanning process completes. Then, press `OK` to return to xref:install/Installing_Using_Anaconda.adoc#sect-installation-gui-storage-partitioning[Installation Destination]; all detected disks including any new ones will be displayed in the `Local Standard Disks` section.
	The `Specialized & Network Disks` section below shows advanced network storage (such as iSCSI and FCoE disks) currently configured. When you first open this screen, no such devices will be displayed because they can not be automatically detected; to search for network storage devices, press `Add a disk` button and proceed with xref:Installing_Using_Anaconda.adoc#sect-installation-gui-installation-destination[Installation Destination - Specialized & Network Disks]. Any network storage you configure will then show up in the `Specialized & Network Disks` the same way local disks are shown above.
	All storage devices which will be used to install {PRODUCT} have a black circle icon with a white check mark on them. Disks not marked by this icon will not be used during the installation - they will be ignored if you choose automatic partitioning, and they will not be available in manual partitioning.
	USB storage devices such as flash drives and external disks will be shown in the `Local Standard Disks` as well, and they will be available for selection the same way internal hard drives are. Make sure to not select any removable storage as installation targets unless you really want to do so. If you accidentally use a removable drive to install {PRODUCT} and then unplug it, your system will likely become unusable.
	Unselected and Selected Disk	선택하지 않고 선택한 디스크
	Disk selection in the Installation Destination screen. Two disks are displayed; only the one on the right side will be used	설치 대상 화면에서 디스크 선택. 두 개의 디스크가 표시되었습니다; 우측에 있는 한 개만 사용 될 것입니다
	anaconda/StorageSpoke_Selected.png	anaconda/StorageSpoke_Selected.png
	After you select all disks you want to install {PRODUCT}, select one of the two options in the `Other Storage Options` section:	{PRODUCT}를 설치 하고자 하는 모든 디스크를 선택한 후에, `기타 저장소 선택` 부분에서 두 가지 옵션 중 하나를 선택합니다:
	`Automatically configure partitioning` - If this option is selected, then after you press `Done` in the top left corner of the screen, the installer will determine the total amount of space on all selected disks, and it will create a _Logical Volume Management_ (LVM) layout suitable for your system. The specifics of this layout depend on whether your system uses BIOS or UEFI firmware, the total amount of free space on your disks, and the amount of RAM on your system (which determines the size of your swap space).
	With automatic partitioning, you can also select the `I would like to make additional space available` option below. Use this option if you want to reclaim space from an existing partitioning layout - for example, if a disk you want to use already contains a different operating system, and you want to make this system's partitions smaller to allow more room for {PRODUCT}. The `Reclaim space` dialog which opens if this option is selected is described later in this section.
	`I will configure partitioning` - Select this option and press `Done` in the top left corner of the screen to configure your system's partitioning layout manually. This requires some knowledge of the theory behind disk partitions and related concepts, but gives you full control over the way the system will be installed. For instructions for manual partitioning, see xref:Installing_Using_Anaconda.adoc#sect-installation-gui-manual-partitioning[Manual Partitioning].
	Additionally, you can select `Encrypt my data`pass:attributes[{blank}]; this will encrypt all partitions except the ones needed to boot the system (such as `/boot`) using _Linux Unified Key Setup_ (LUKS). Encrypting your hard drive is recommended. For detailed information about LUKS encryption, see the [citetitle]_{PRODUCT} Security{nbsp}Guide_, available at link:++https://docs.fedoraproject.org/++[].
	If you lose the LUKS passphrase, any encrypted partitions and the data on them will become completely inaccessible. There is no way to recover a lost passphrase. However, if you perform a Kickstart installation, you can save encryption passphrases and create backup encryption passphrases during the installation. See xref:advanced/Kickstart_Installations.adoc#chap-kickstart-installations[Automating the Installation with Kickstart] for information about Kickstart installations.
	To control which one of your selected storage devices will contain the _boot loader_, click the `Full disk summary and bootloader` link in the bottom left corner of the screen, and follow the instructions in xref:install/Installing_Using_Anaconda.adoc#sect-installation-gui-storage-partitioning-bootloader[Boot Loader Installation]. Note that while in most cases it is sufficient to leave the boot loader in the default location, some configurations (for example, systems which require _chain loading_ from another boot loader) will require the boot drive to be specified manually.
	After you select storage devices, choose between automatic and manual partitioning, configure encryption and boot loader location, press `Done` in the top left corner of the screen. Then, depending on your settings, the following will happen:
	If you chose to encrypt your hard drive, the `Disk Encryption Passphrase` dialog will appear. Enter your chosen passphrase into the `Passphrase` and `Confirm` fields. When you do so, the passphrase will be automatically evaluated and its strength will be displayed, along with suggestions on how to make it stronger if the installer has determined it to be weak. For information about creating strong passwords, see [citetitle]_{PRODUCT} Security{nbsp}Guide_.
	If you selected automatic partitioning and the `I would like to make additional space available`, or if there is not enough free space on your selected hard drives to install {PRODUCT}, the `Reclaim Space` dialog will appear. This dialog lists all disk devices you have configured and all partitions on those devices. The bottom right corner of the dialog displays information about how much space the system needs for at least a minimal installation and how much space you have reclaimed.
	If you use the `Reclaim Space` dialog to delete a partition, all data on that partition will be lost. If you want to preserve your data, use the `Shrink` option, not the `Delete` option.
	First, review the displayed list of available storage devices. The `Reclaimable Space` column shows how much space can be reclaimed from each entry. To reclaim space, select a disk or partition, and press either the `Delete` button to delete that partition (or all partitions on a selected disk), or `Shrink` to use free space on a partition while preserving existing data. Alternatively, you can press `Delete all` in the bottom right corner; this will delete all existing partitions on all disks and make this space available to {PRODUCT}, but all existing data on all disks will be lost.
	After you free enough space for your {PRODUCT} installation, press `Reclaim space` to finish.	자신의 {PRODUCT} 설치를 위한 충분한 공간을 확보한 후에, `공간 확보`를 눌러 완료하세요.
	No changes to any disks will be made until you press `Begin Installation` in xref:Installing_Using_Anaconda.adoc#sect-installation-gui-installation-summary[Installation Summary]. The `Reclaim Space` dialog only marks partitions for resizing or deletion, but no such action is performed immediately.
	If you selected the `I will configure partitioning` option, pressing `Done` will open the `Manual Partitioning` screen. See xref:Installing_Using_Anaconda.adoc#sect-installation-gui-manual-partitioning[Manual Partitioning] for further instructions.

Loading…

simmon

Translation changed

English

Korean 8 characters edited Current translation

3 years ago

simmon

Translation added

English

Korean 30 characters edited

3 years ago

Browse all string changes

Things to check

Unchanged translation

Source and translation are identical

Reset

Glossary

English	Korean
Anaconda	아나콘다	fedora-docs-l10n/fedora-install-guide

String information

Source string description

type: Target for macro image

Flags

no-wrap

Source string location

./pages/_partials/install/StorageSpoke.adoc:38

String age

3 years ago

Last updated

a year ago

Source string age

4 years ago

Translation file

po/ko/f31/pages/_partials/install/StorageSpoke.po, string 14

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the last translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.